Printer Won't Connect to Wi-Fi? Checks to Run First
Printer Won't Connect to Wi-Fi? Checks to Run First

Photo by Mikhail Nilov on Pexels
If your printer won't connect to Wi-Fi, start with the network name and password shown on the printer. If it already has an IP address, check whether Windows can see it before resetting the printer. These checks help pinpoint whether the fault is in wireless setup or the print queue.
Work through the checks below in order. They start with the most common cause and move towards the less likely ones, so you are not wasting time on a complicated fix when the real problem is a typed password.
1. Printer won't connect to Wi-Fi? Check the network name and password
This is the single most common reason a printer stops connecting. If you have changed broadband provider, had a new router fitted, or simply changed your Wi-Fi password, the printer is still holding the old details. It will keep trying to reach a network that no longer exists, or knock on the door with a password that has since been changed.
You need to re-enter the current network name and password on the printer itself, using its control panel, or run the wireless setup again from the printer manufacturer's app on a computer or phone. A few practical points:
-
Type the password exactly, paying attention to capitals and any symbols. Wi-Fi passwords are case sensitive.
-
Pick your own network from the list rather than a neighbour's similarly named one. Look for the exact name on the router label or in your phone's Wi-Fi settings.
-
If the printer asks for a password and rejects it repeatedly, try entering it on a phone first to confirm you have the right one.
2. Restart everything in the correct order
The order matters here, and it is where a lot of people go wrong. Turning everything off and on again in a random sequence often leaves the printer and the router still disagreeing about who is connected to what. Follow this routine instead:
-
Turn the printer off.
-
Switch the router off and leave it off for around 30 seconds.
-
Power the router back up and wait until the internet connection has settled. Give it a couple of minutes rather than a few seconds.
-
Only then turn the printer back on.
-
Wait a further minute or two before testing a print job.
That pause gives the router time to finish its own start-up routine, so when the printer comes looking for the network, the network is genuinely ready to answer.
3. Wake the printer and put it into setup mode
Printers are aggressive about power saving, and a sleeping printer will often ignore a connection request entirely. On many models, pressing the Cancel button once is enough to wake it. If the printer has a small screen, check that the wireless icon is showing and that it is not displaying a warning.
Some printers also only accept a new network when they are actually in wireless setup mode. On certain models this is triggered by pressing the Cancel button and the Wireless button together, but the exact combination varies enormously between manufacturers and models. Rather than guessing, check the quick start sheet that came with the printer or look up the model on the manufacturer's support pages. Getting the printer into the right mode first saves a lot of failed attempts.
4. Look at the settings on the computer
If the printer appears to be connected but Windows cannot find it, the fault may be on the computer side. A few things are worth checking:
-
Make sure the computer is connected to the same Wi-Fi network as the printer. It is surprisingly easy for a laptop to be holding on to a different network, especially in a house with more than one router or an extender.
-
In the printer's connection settings, check that the Active Adapter is set to Auto so the machine is not locked to a wired or outdated connection type.
-
Confirm the correct Wi-Fi network is selected in the printer's own network menu, not an old saved entry.
If the printer shows as offline in Windows, restart the print spooler or simply reboot the computer once. A stale print queue can make a perfectly healthy printer look broken.
5. Remove the printer and add it back
Sometimes the driver and the printer have fallen out with each other and no amount of reconnecting will fix it. The clean way to deal with this is to uninstall the printer from the computer completely, then reinstall it, either through Windows or using the manufacturer's own software. This clears out old settings and forces a fresh handshake between the two devices. It takes a few minutes and is a normal step in Windows printer troubleshooting rather than a sign that something is badly wrong.
6. Think about distance, walls and interference
Wireless signal drops off quickly through walls, and printers are often tucked away in the worst possible spot: a cupboard, a spare room, or a corner behind a filing cabinet. As a quick test, move the printer closer to the router temporarily and see whether it connects. If it does, the problem is coverage rather than settings, and the answer is likely to be repositioning the printer, moving the router, or improving coverage in that part of the building.
It is also worth checking how many devices are competing for the connection. A busy household network can leave a printer struggling to hold on.
7. When the printer is on the Wi-Fi but still will not print
There is a difference between a printer that cannot see the network and one that is on the network but cannot reach the internet. Some printers show a message along the lines of "printer not connected to the internet" when they cannot reach the services they depend on, including manufacturer subscription and ink services. If your printer is linked to a scheme like that, the message may be about the account connection rather than printing itself.
If the printer can print a network configuration page from its own control panel, do that. It confirms the printer's view of the network and is exactly the information anyone helping you will ask for. The manual for your model will show you which buttons to press.
8. Know when to stop and get help
If you have worked through the checks above and the printer still will not join the network, the remaining causes tend to be router settings, network configuration problems or a genuine hardware fault in the printer's wireless card. Those are awkward to diagnose without the right tools, and continuing to press buttons at random rarely helps.
FixPoint IT Support covers Basildon and the surrounding Essex area, including home Wi-Fi and network help, printers, laptops and desktops. Work is carried out on a no fix, no fee basis with the price agreed upfront before anything chargeable happens, and rates start from £45. That means you know what you are paying before you commit, which is more than most people get from a call centre script.
If the printer is online but jobs get stuck, use our home printer setup and troubleshooting guide or follow Microsoft’s steps for an offline printer. If phones and laptops also disconnect, start with our Wi-Fi dropout walkthrough.
Frequently Asked Questions
Why did my printer stop connecting after I changed the Wi-Fi password?
Because the printer is still trying to use the old password. Changing the password on the router does not update the printer, so the two can no longer agree. Re-enter the current network name and password on the printer's control panel, or run the wireless setup again from the manufacturer's app, and it should reconnect.
Should I reset the printer's Wi-Fi settings?
A reset clears any saved network details and returns the printer to its initial setup state, which removes stale information left over from an old router or password. It is a sensible step when re-entering details has failed. How you do it depends on the model, so check the manual or the manufacturer's support pages first.
My printer shows as connected but nothing prints. What now?
Check that the computer is on the same network as the printer and that the correct printer is selected rather than a duplicate entry. Clear any stuck jobs in the print queue, restart the computer, and if that fails, uninstall the printer and add it back. That usually clears a stubborn connection problem.
How do I put the printer into wireless setup mode?
It varies by manufacturer and model. On some printers, pressing the Cancel button and the Wireless button together starts the process, but plenty of models use a different combination or a menu option on the screen. Your quick start sheet or the manufacturer's support page will give you the exact sequence.
Do I always need to restart the router?
Not always, but it is worth doing when a printer refuses to connect, and the order matters. Switch the router off for around 30 seconds, turn it back on and let the connection settle, then power up the printer. This gives both devices a clean start and rules out a simple handshake failure.